Fosroc Construction Chemicals

Renderoc CS

Product Details:
  • Brand: Fosroc

Renderoc CS is used for sealing cracks on plaster, masonryand concrete substrates.
details -
  • Colour -White
  • Setting time -15 to 20 min
  • Compressive  strength -22 N/mm2 in 7 days
  • Fresh  wet  density 1.95  g/cc W/p Ratio 0.36
  • Mix proportions by volume 1 part water : 2.5 -3 parts of powder
  • Minimum  application temperature -10C

Conplast WL

Product Details:
  • Type: Concrete Admixture, Construction Adhesives & Sealants, Floor Hardeners, Protective Coatings & Resins, Water Proofing Compounds
  • Application: Roofs, Tanks, Walls, Terrace, Basements
  • Form: Liquid, Powder, Solvent, Aerosol
  • Brand: fosroc

We are offering wide spectrum of construction chemicals such as Conplast WL that is widely used to enhance water proofing properties of concrete and cement mixtures in variety of critical application areas such as roofing, bathroom flooring, water tanks, and so forth. It designed to mix instantly to form homogeneous mix and remarkably reduces permeability of concrete. It also offers better compaction of concrete to provide dense output without scope for porosity.

Features:

  • Flawless composition
  • Immaculate finish

Details -

  • Chloride content-As per IS:2645-2003
  • Conplast WL is supplied in 125ml, 1, 5 , 20 and 200 litre
    containers
  • Permeability to water: Less than 15% as compared to 50% max. allowable under IS:2645compared to control sample

    Fosroc Lokfix P Base

    Lokfix is a two-component polyester resin anchoring grout, meeting the requirements of BS EN 1504-6: Anchoring of reinforced steel bars.

    Supplied in pre-measured quantities, the material cures quickly to give consistent, high performance anchorages. The two versions of Lokfix available are :

    Lokfix S25 : Pourable grade, 25 minute gel time at 20°C for use in vertical down holes where the hole is 8 to 40 mm greater in diameter than the bar.

    Lokfix P25 : Thixotropic grade, 25 minute gel at 20°C for use in overhead or horizontal holes where the hole is up to 25 mm greater in diameter than the bar. The thixotropic nature of Lokfix P25 reduces flow of grout out of the hole.

    • Rapid strength gain.
    • Vibration resistant.
    • Corrosion resistant.
    • Non-expansive.
    • Can be placed underwater

    Details -

    • Flash point- 29 deg C
    • Lokfix S/P/L - 0.5 and 2.5 L Pack
    • Compressive strength - 70N/mm2 in 7 days

    Conbextra EP10

    Product Details:
    • Brand: Fosroc

    Conbextra EP10

    Fosroc has been servicing grout requirement of Indian industry for more than three decades. Conbextra range of Cementations and Epoxy grouts are considered to be the most dependable grouting solutions by engineers, erectors and machine manufacture. The journey started way back in mid-eighties when Indian power sector accepted the locally produced Conbextra GP2 and stopped importing cement grouts from European sources.

    Specifications -
    • Pot life- 90 min. @ 20 °C -40 min. @ 35°C
    • Density -approx. 1050 kg/m3
    • Tensile strength- 26 N/mm2 @ 7 days

    Fosroc Cebex 100

    Product Details:
    • Brand: Fosroc

    Cebex 100
    Fosroc has been servicing grout requirement of Indian industry for more than three decades. Conbextra range of Cementations and Epoxy grouts are considered to be the most dependable grouting solutions by engineers, erectors and machine manufacture. The journey started way back in mid-eighties when Indian power sector accepted the locally produced Conbextra GP2 and stopped importing cement grouts from European sources.

    Details -
    • Chloride content-Nil  as  per  BS:5075
    • Time for expansion- 15  minutes  -  2  hours. Temperatures  above  20 Cmay  slightly  reduce  these times.
    • Limitations-Cebex 100 is incompatible with High Alumina Cement.

    Hydroproof Xtra

    Product Details:
    • Grade Standard: Technical Grade
    • Physical State: Powder, solid
    • Usage: Industrial

    Product Details:
    ApplicationConstruction
    Form of ChemicalLiquid, Solid
    CategoryWaterproofing Coating, Cementitious Waterproofing, Crystalline Waterproofing, Acrylic Based Polymer Coating, Bitumen Membrane
    BrandFosroc

    Hydroproof Xtra is formulated to be mixed with cement on site or simply brush applied over concrete or masonry surfaces to provide an effective waterproof membrane.

    • Non - toxic, non-fl ammable and user friendly
    • Provides a tough, impermeable waterproof membrane
    • Can be applied by brush, on horizontal and vertical surfaces
    • Excellent adhesion to concrete and masonry surfaces
    • Protects concrete and mortar from natural elements such as wind, rain, sunlight
    • Breathable - allows inside water vapour to escape

    Brushbond TGP

    Product Details:
    • Application: Construction
    • Form of Chemical: Liquid, Solid, Slurry
    • Category: Waterproofing Coating, Cementitious Waterproofing, Crystalline Waterproofing, Acrylic Based Polymer Coating, Bitumen Membrane
    • Brand: Fosroc

    Brushbond TGP is an economical cementitious coating system designed for waterproofing concrete against low positive or negative hydrostatic water pressure in a wide variety of structures such as:

    • Sewage treatment and water treatment plants
    • Water tanks
    • Concrete pipes
    • Manholes

    Advantages:

    • Penetrates concrete, seals capillary tracts and hairline cracks
    • Contains no chlorides
    • Easy to apply, cost effective in use
    • Can be applied to new or old concrete in both interior and exterior locations
    • Suitable above or below ground
    • Surface damage will not affect the system

     

    Specifications -
    • Brushbond TGP :1 to 1.5 kg/m 2per application (brush)
    • Brushbond TGP :20 kg bags
    • effectiveness ofBrushbond TGP may require - 2-3 weeks

    Colpor 200 Hardener

    Product Details:
    • Surface of Application: Ceramic
    • Grade Standard: Industrial Grade
    • Features: Impact Resistant, Moisture Resistant, Vibration Resistant, Heat Resistant, Water Resistant
    • Brand: Fosroc

    Colpor 200 is resistant to jet blast and is suitable for concrete runways and hard-standings and areas where fuel spillage is likely.

    • High movement accommodation
    • Cold applied — no heating equipment required
    • Fuel, oil and hydraulic fluid resistance
    • Jet blast resistant

    Specifications -

    • Form-Two part compoundBase compound: viscous liquid
    • Curing agent: liquid
    • Colour- black
    • Setting time -After 10 to 16 hours @ 35°C Colpor 200 will be tack free and can accept traffic

    Conbextra EP75

    Product Details:
    • Brand: fosroc

    Conbextra EP75 is a solvent free epoxy resin grout designed for grouting of gap widths of 10 to 75 mm. It is supplied as a three component system consisting of base, hardener and specially graded aggregate. The components are supplied in the correct mix proportions designed for whole pack mixing on site.

    • Creep resistant -to Improve resistance to deformation under constant loading.
    • Excellent durability - high compressive, flexural and tensile strengths ensure a long working life.
    • Cost effective - high early strength gain promotes minimum downtime and early commissioning of plant.
    • User friendly - simple, full pack mixing to ensure that the performance characteristics are achieved.
    • Versatile - suitable for a wide range of loading situations including repetitive dynamic loads.
    • Excellent in service performance - non-shrink capability ensures full surface to surface contact.

     

    Properties-
    • Pot Life -2 hours @ 23°C
    • Tensile strength- 14 N/mm2at 7 days
    • Flexural strength-  26 N/mm2 at 7 days

    Cobextra UHS

    Product Details:
    • Grade Standard: Technical Grade
    • Physical State: Powder, solid, Liquid, Granules, Crystals
    • Usage: Industrial

     

    Conbextra UHS is supplied as a ready-to-use dry powder, requiring only the addition of water to produce a free flowing non-shrink grout. The material is a blend of specially processed cement, pre-graded fillers and additives which impart.

    • High early and final strengths due to very low water requirement.
    • Controlled expansion to retain the original volume filled even after setting.
    • Free flow characteristics without any segregation and bleeding.
    • Conbextra UHS, on setting, will have a micro-cellular structure with high frost, fire and oil resistance.
    • Non shrink - Will continue to occupy the filled spaced without shrinkage.
    • High strength - Can be used under heavy duty machines and equipment with high operational and static loads.
    • Free flow - Ensures high level of contact with load bearing areas. Also helps complete fi lling without voids. No need for external aids like rodding, poking, chaining etc.
    • Prepacked and factory controlled : Consistency and reliability ensured. Site batching and blending variations eliminated.
    • Chloride free : Does not cause corrosion of machine parts, anchor bolts etc., in contact with grout.
    • Hydrogen free : Non metallic expansion system.

    Properties -

    • Young's modulus: 28 kN/mm2
    • Flexural strength: 120 kg/cm2( BS 4551, 1980 )
    • Tensile strength :  At 28 days tensile strength  achieved istypically 45kg/cm2

    Fosroc Concure LP

    Product Details:
    • Grade Standard: Technical Grade
    • Physical State: Powder, solid, Liquid, Granules
    • Usage: Industrial

    Spray applied membrane to retain moisture in concrete for effective curing. 

    Suitable for all general concreting applications and of particular benefit for large area concrete surfaces, such as airport runways, roads and bridgeworks. 

    • Improved curing of concrete enhances cement hydration and provides a more durable concrete
    • Control of moisture loss improves surface quality, reducing permeability, producing a hard wearing, dust free surface and minimising potential for surface cracking and shrinkage
    • Light reflective grades minimise solar temperature gain
    • Spray application reduces labour costs and eliminates the need for alternative curing systems

     

    properties-
    • Specific Gravity - 0.82 - 0.85
    • Efficiency - more than 90%
    • coverage rate -is between 3.5 and 5.0 m 2/ litre (0.200 to 0.285 litres/m2)

    Conplast SP430 DIS

    Product Details:
    • Brand : Fosroc

    Conplast SP430 G8 is based on Sulphonated Napthalene Polymers and supplied as a brown liquid instantly dispersible in water.

    Conplast SP430 G8 has been specially formulated to give high water reductions upto 25% without loss of workability or to produce high quality concrete of reduced permeability.

    Advantages:

    • Improved workability - Easier, quicker placing and compaction.
    • Increased strength - Provides high early strength for precast concrete with the advantage of higher water reduction ability.
    • Improved quality - Denser, close textured concrete with reduced porosity and hence more durable.
    • Higher cohesion - Risk of segregation and bleeding minimised; thus aids pumping of concrete.
    • Chloride free - Safe in prestressed concrete and with sulphate resisting cements and marine aggregates
    Properties
    • Specific gravity: 1.20 to 1.22 at 30C
    • Air entrainment - Approx. 1% additional air over control
    • Chloride content-Nil.  as  per  IS:9103-1999 and  BS:5075

    Fosroc Brushbond

    Product Details:
    • Grade Standard: Technical Grade
    • Physical State: Powder, solid, Granules
    • Usage: Industrial

    Brushbond is a cementitious coating for application to concrete and brickwork to provide a waterproof barrier and fiil out surface imperfections.Suitable for sealing water tanks,reserviors,toilets and bathrooms,balconies and basements as well as filling blowholes,cracks,imperfections and for providing concrete surfaces with a uniform appearance.

    Advantages:

    • Minimum surface preparation needed
    • Excellent adhension.Bonds directly to porous and non- porous surfaces
    • Waterproof and non-toxic-Ideal for potable water tanks
    • Excellent for damp-proofing basements below ground
    • Breathable-Allows transmission of water vapour from interior of building
    • High resistance to carbon dioxide and chloride ion diffusion
    • Can fill the honeycomds, dot surfaces and concrete with potholes

    Properties -
    • Pot life at 20C- 1  hour
    • Mixed Density -1.90kg/ltr.  (brushable consistency)
    • Colours -Grey and white
    • Toxicity -Non-toxic

    Fosroc Conbextra GP2

    Product Details:
    • Brand: Fosroc

    Specifications

    Product

    Description

     

    W/P Ratio

    Flow

    Compressive Strength

    *All Strength are in mm Square.

     

     

    Flexural Strength

    Recommended Applications

     

     

     

     

     

     

     

     

     

     

     

     

    Cement Grouts

     

     

     

    1D

    3D

    7D

    28D

    28Days

     

    Conbextra GP1

    Non shrink Xementious Grout

    ASTM C 1107 Type A

    0.15

    >20 cm

    10 N/mm

    27 N/mm

    35 N/mm

    45 N/mm

     

    Static Load applications like steel column foundation , pipe rack foundation and equipment with only static load

    Conbextra GP2

    Plastic Shrinkage compensated , high flow, high strength cementations grout with low exothermic heat

    ASTM C 1107 Type A

    0.18

    >20 cm

    24 N/mm

    45n/mm

    55n/mm

    65n/mm

    10n/mm

    Machine foundation grout with both Static and dynamic loads,bridge bearings, precast construction etc.

    Conbextra GP2 N

    Plastic Shrinkage compensated, high flow, high strength cementitious grout with low exothermic

    ASTM C 1107 Type A

    0.16

    >20 cm

    24 N/mm

    45n/mm

    55n/mm

    65n/mm

    10n/mm

    Machine foundation grout with both Static and dynamic loads,bridge bearings, precast construction etc.

    Fosroc Decofill

    Product Details:
    • Grade Standard: Technical Grade
    • Physical State: Powder, solid, Granules, Crystals
    • Usage: Industrial

    Details -
    • Colour-white
    • Physical or chemical change- curing by loss of water
    • Application temp.-5-40 deg C
    • Cure rate- 3-5  days  depending  on thickness,  ambient temperature  and  humidity

    Fosroc Nitobond AR

    Product Details:
    • Type: Epoxy Based
    • Grade Standard: Industrial Grade
    • Brand: Fosroc

    Nitobond AR is a modified acrylic emulsion which is specially designed for use as a bonding aid, curing agent and gauging liquid for cementitious systems. It is resistant to hydrolysis and can therefore be used for external application.

    • Single component gauged as required.
    • Simply brushed onto concrete as a primer.
    • Provides excellent bond to concrete, masonry, stonework, plaster and block-board.
    • Improves tensile and compressive properties. Allows thin section applications.
    • Compatible with all common hydraulic cements.
    • Suitable for use in Middle East conditions. Used as a curing membrane.
    • Is economical in use.

    Details -

    • Coverage--Approximately 6 - 8m2/ litre depending on substrate
    • Shelf life-6 months at 30C. Nitobond AR should be protected from frost
    • Flash point : 48C

    Nitocote ET Hardener

    Product Details:
    • Types: Solid , Water-Based , Solvent-Based
    • Category: Floor Coating , Wall Coating
    • Features: Chemical Resistant , UV Resistant , Impact Resistant , Abrasion Resistant
    • Grade Standard: Industrial Grade , Technical Grade , Chemical Grade

    Applications -
    • High build, single coat application
    • Good chemical resistance.
    • Primerless.
    • Excellent hold-out on vertical surfaces.
    • Moderate flexibility.
    Details -
    • Pot life - 2  hrs
    • Time between coats- 4 hrs
    • Full hardness- 24hrs
    • Full Cure- 7 days
    • Compressive Strength -40  N/mm2

    Nitocote SN522

    Product Details:
    • Application: Construction
    • Form of Chemical: Liquid, Solid, Slurry
    • Category: Waterproofing Coating, Cementitious Waterproofing, Crystalline Waterproofing, Acrylic Based Polymer Coating, Bitumen Membrane
    • Brand: Fosroc

    Nitocote SN522 is a single component, penetrating silane-siloxane which penetrates into porous substrates and then reacts to produce a bonded water repellent lining. Although allowing water vapour to escape from the substrate, it significantly reduces the absorption of water and water-borne salts.

    • Penetrates into substrates.
    • Non-staining.
    • Reduces water and chloride intrusion.
    • Increases freeze thaw resistance.
    • Minimises efflorescence.
    • Allows water vapour to escape from the structure.
    • Resistant to atmospheric contaminants

    Details -

    • Mixed Density -1.90kg/ltr.  (brushable consistency)
    • Colours -Grey and white
    • Toxicity -Non-toxic
    • Flash point-38 deg C

    Nitoflor Hardtop STD

    Product Details:
    • Brand: Fosroc

    Nitoflor Hardtop Standard is quality controlled, factory blended powder which are ready to use on site. They contain special hardwearing aggregates which have been selected for abrasion and wear resistant properties as well as shape and size. These latter considerations, together with the use of high performance workability admixtures, produces a material which is easy to trowel into the surface of fresh, wet concrete. Nitofl or Hardtop Standard cure monolithically to provide a dense, non-porous surface which is extremely hardwearing and abrasion resistant. Monolithic cure ensures that problems normally associated with thin ‘granolithic’ screeds, viz., shrinkage, cracking, etc., are completely overcome.

    Being non-metallic, Nitoflor Hardtop Standard provide a non-slip surface which will never rust and disintegrate.

    • Non metallic - does not rust or stain.
    • Provides a hard, abrasion resistant surface
    • Forms monolithic bond with base concrete
    • Easy and economical to apply

    Details -

    • Abrasion resistance -( IS : 1237 - 1980)
    • Base concrete -of  300  kg/m3
    • Fire -Nitoflor Hardtop / Nitoflor Hardtop Standard are not flammable

    Nitomortar S

    Product Details:
    • Brand: Fosroc

    Nitomortar S is a high strength epoxy mortar, based on a high quality solvent-free epoxy resin system. The special silica aggregates provide high strength and excellent abrasion resistance.

    Nitomortar S is a three-component material supplied in pre-weighed quantities ready for on-site mixing and use.

    • High ultimate strength — suitable for structural use
    • Early development of strength minimises disruption
    • Abrasion-resistance — suitable for heavily trafficked areas
    • Highly resistant to a wide range of chemicals
    • Cured product is highly impermeable to water when ‘tight trowel’ finished
    • Typically twice as strong as good quality concrete
    • Pre-weighed components ensure consistency

    Details -

    • Compressive strength (BS 6319, Pt 2)- 60N/mm2@ 7 days
    • Flexural strength (BS 6319 Pt 3) -20N/mm2 @ 7 days
    • Tensile strength(ASTM C 307) -10N/mm 2@ 7 days
    • Pot life -20 mins @ 35C
    • Initial hardness -24 hours
    • Full cure-7 days

    Nitoprime 25

    Nitoprime 25 is a two component solvent containing primer consisting of modified epoxy resin based primer.

    It is used in conjunction with Nitomortar, Nitoflor and Nitocote products.

    • Easily applied by brush or roller.
    • Long open time.
    • High wetting out characteristics.
    • High performance.

    details -

    • Pot life - 90 minutes
    • Recommended  application  range  is  - 10-40 deg C
    • Approximate coverage rate -5.5 - 6.5 m2/ltr

    Renderoc HS XTRA

    Product Details:
    • Brand : fosroc

    Renderoc FC cementitious, polymer modified, fairing coat is designed for vertical and overhead use to infill honeycombing and voids up to 3 mm deep in the surface of concrete which is not trafficked and is subsequently coated.
    Renderoc FC is supplied as a ready to use blend of dry powders requiring only the site addition of clean water to produce a highly consistent cementitious fairing mortar. The material has good handling characteristics, while minimising water demand.The product exhibits excellent thermal compatibility with concrete and is fully compatible with other Renderoc mortars and Dekguard coatings. 

    • Compatibility with non-structural concrete of compressive strength 20 - 35 MPa
    • Polymer-modification provides extremely low permeability to water, carbon dioxide and chlorides
    • Excellent bond to concrete
    • Can be applied quickly and efficiently
    • One component, pre-bagged to overcome site-batched variations
    • Contains no chloride admixtures

    Details -

    • Coefficient of thermal expansion: 7 - 12x 10-6/°C
    • Working life:Approximately 20 minutes**
    • Setting time (BS 4550):30 minutes - 1 hour**
    • Fresh wet density:Approximately 2000 kg/m³

    Renderoc FC

    Product Details:
    • Brand : Fosroc

    Single part, non shrink, cementitious, crack sealerfor plaster, masonry and concrete

    Renderoc FC cementitious, polymer modified, fairing coat is designed for vertical and overhead use to infill honeycombing and voids up to 3 mm deep in the surface of concrete which is not trafficked and is subsequently coated.
    Renderoc FC is supplied as a ready to use blend of dry powders requiring only the site addition of clean water to produce a highly consistent cementitious fairing mortar. The material has good handling characteristics, while minimising water demand.The product exhibits excellent thermal compatibility with concrete and is fully compatible with other Renderoc mortars and Dekguard coatings. 

    • Compatibility with non-structural concrete of compressive strength 20 - 35 MPa
    • Polymer-modification provides extremely low permeability to water, carbon dioxide and chlorides
    • Excellent bond to concrete
    • Can be applied quickly and efficiently
    • One component, pre-bagged to overcome site-batched variations
    • Contains no chloride admixtures

    Details -

    • Coefficient of thermal expansion: 7 - 12x 10-6/°C
    • Working life:Approximately 20 minutes**
    • Setting time (BS 4550):30 minutes - 1 hour**
    • Fresh wet density:Approximately 2000 kg/m³

    Auramix

    Product Details:
    • Appearance: Yellowish to Brownish liquid
    • Specific Gravity : 1.0 3 - 1.07

    Auramix  is a strong superplasticiser allowing production of consistent concrete properties around the required dosage.

    • Increased retardation controls the heat of hydration and
    • yields high ultimate strength
    • Higher E modulus
    • Improved adhesion to reinforcing and prestressing steel
    • Better resistance to carbonation
    • Lower permeability
    • Better resistance to aggressive atmospheric conditions
    • Reduced shrinkage and creep
    • Increased durability

    Auramix DIS

    Product Details:
    • Appearance: Yellowish to Brownish liquid
    • pH: Minimum 6.0
    • Packaging Size: 20kg
    • Packaging Type: Drum

    Auramix 400 combines the properties of water reduction and workability retention. It allows the production of high performance concrete and/or concrete with high workability.

    • Low viscosity suitable for pumping of different grades of
    • concrete to higher fl oors
    • Higher E modulus
    • Improved adhesion to reinforcing and prestressing steel
    • Better resistance to carbonation
    • Lower permeability
    • Better resistance to aggressive atmospheric conditions
    • Reduced shrinkage and creep
    • Increased durability

    Brushcrete

    Product Details:
    • Application: Construction
    • Form of Chemical: Liquid, Solid, Slurry
    • Category: Waterproofing Coating, Cementitious Waterproofing, Crystalline Waterproofing, Acrylic Based Polymer Coating, Bitumen Membrane
    • Brand: Fosroc

    Brushcrete is a single component acrylic based polymer when blended with cement forms a composite polymer modified cementitious waterproofi ng system, when used in conjunction with fi bre mesh forms a tough hard wearing surface.

    Advantage:

    • Can be applied in uniform thickness to horizontal and vertical surfaces.
    • Develops excellent bond to most building materials.
    • Improves mechanical physical properties of the coating system when used in conjunction with cement.
    • Reduces or prevents salt penetration into concrete.
    • Resistance to ultraviolet light or by chemicals ranging from mild acids to strong alkalies.
    • Is highly impermeable in continuous wet condition.
    • Is non-flammable and does not give off toxic gases, when exposed to fire.
    • Non toxic

    Properties :
    • Pot life:20-30 min. at 300C
    • Mixed Density of:2.1-2.2 g/cc.
    • brushcrete  topping Colour:White  liquid
    • Application  temperature:>  100C <35 oC
    • Bond  strength  with  concrete :>  1N/mm2

    Concure NB STD

    Product Details:
    • Grade Standard: Technical Grade
    • Physical State: Powder, solid, Liquid, Granules, Crystals
    • Usage: Industrial

    Concure WB is a water based concrete curing compound based on a low viscosity wax emulsion. It is supplied as a white emulsion which forms a clear film on drying.
    When first applied to a fresh cementitious surface the emulsion breaks to form a continuous, non-penetrating white coating.
    This dries to form a continuous clear film which provides a barrier to moisture loss, ensuring more efficient cement hydration, improved durability and reduced shrinkage.

    • Improved curing of concrete enhances cement hydration and provides a more durable concrete
    • Control of moisture loss improves surface quality, reducing permeability, producing a hard wearing, dust-free surface and minimising potential for surface cracking and shrinkage
    • Fugitive colour provides visual guide during application
    • Water based, therefore, non-flammable
    • Spray application reduces labour costs and eliminates the need for alternative curing systems

     

    Properties -
    • Colour- White
    • Minimum application temperature - 10 degree C
    • Curing efficiency :  Concure WB curing agent complies with the  internationally recognised ASTM C309-90 standard.

    Concure WB White

    Product Details:
    • Application: Construction
    • Form of Chemical: Liquid, Solid, Slurry
    • Category: Waterproofing Coating, Cementitious Waterproofing, Crystalline Waterproofing, Acrylic Based Polymer Coating, Bitumen Membrane
    • Brand: Fosroc

    Concure WB is a water based concrete curing compound based on a low viscosity wax emulsion. It is supplied as a white emulsion which forms a clear film on drying.
    When first applied to a fresh cementitious surface the emulsion breaks to form a continuous, non-penetrating white coating.
    This dries to form a continuous clear film which provides a barrier to moisture loss, ensuring more efficient cement hydration, improved durability and reduced shrinkage.

    • Improved curing of concrete enhances cement hydration and provides a more durable concrete
    • Control of moisture loss improves surface quality, reducing permeability, producing a hard wearing, dust-free surface and minimising potential for surface cracking and shrinkage
    • Fugitive colour provides visual guide during application
    • Water based, therefore, non-flammable
    • Spray application reduces labour costs and eliminates the need for alternative curing systems

    Properties -

    • Colour- White
    • Minimum application temperature - 10 degree C
    • Curing efficiency :  Concure WB curing agent complies with
      the  internationally recognised ASTM C309-90 standard.
    • Specific Gravity - 0.82 - 0.85

    Fosroc Nitobond AR

    Product Details:
    • Grade Standard: Technical Grade
    • Physical State: Powder, solid, Liquid, Granules, Crystals
    • Usage: Industrial

    Nitobond AR is a modified acrylic emulsion which is specially designed for use as a bonding aid, curing agent and gauging liquid for cementitious systems. It is resistant to hydrolysis and can therefore be used for external application.

    • Single component gauged as required.
    • Simply brushed onto concrete as a primer.
    • Provides excellent bond to concrete, masonry, stonework, plaster and block-board.
    • Improves tensile and compressive properties. Allows thin section applications.
    • Compatible with all common hydraulic cements.
    • Suitable for use in Middle East conditions. Used as a curing membrane.
    • Is economical in use.

    Details -

    • Coverage--Approximately 6 - 8m2/ litre  depending  on substrate
    • Shelf  life-6 months at 30C. Nitobond AR should be protected from frost
    • Flash point : 48C

    Nitobond SBR Latex

    Nitobond SBR is a polymer bonding aid and mortar additive. Supplied as a ready to use white liquid, it is designed to improve the quantities of site-batched cementitious mortars and slurries. Being resistant to hydrolysis, it is ideal for internal and external applications in conjunction with cement. 

    • Single component liquid can be easily gauged as required
    • Improves cohesion and workability
    • Improves mortars to provide waterproof repairs, renders and toppings which are highly resistant to freeze/thaw cycling
    • Improved tensile and flexural properties allow thin applications
    • Excellent bond to concrete, masonry, stonework, plaster and blockwork
    • Contains no chloride admixtures
    • Can be applied to damp substrates

    Details -

    • Coverage-Slurry  primer  approximately  4-  5  m2/  litre    depending    on substrate  porosity
    • Minimum application temperature- 10 deg C
    • Shelf  life- Nitobond SBR (Latex)  has a shelf life of 12 months if kept in a dry  store  in  unopened  condition
    • Flash point : 48C

    Nitocote ET140 Hardener

    Product Details:
    • Types: Solid , Water-Based , Solvent-Based
    • Category: Floor Coating , Wall Coating , Steel Coating
    • Features: Chemical Resistant , UV Resistant , Impact Resistant , Abrasion Resistant
    • Grade Standard: Industrial Grade , Technical Grade

    Nitocote ET140 is based on solvent-free epoxy resins modified with coal tar pitch. It is supplied as a two pack materials in pre-weighed quantities ready for on-site mixing and use.

    Nitocote ET140 is applied as a two coat application.

    • High build, single coat application
    • Good chemical resistance.
    • Primerless.
    • Excellent hold-out on vertical surfaces.
    • Moderate flexibility.

    Details -

    • Pot life - 2  hrs
    • Time between coats- 4 hrs
    • Full hardness- 24hrs
    • Full Cure- 7 days
    • Compressive Strength -40  N/mm2

    Nitocote EP140

    Product Details:
    • Types: Solid , Water-Based , Solvent-Based
    • Category: Floor Coating , Wall Coating , Steel Coating
    • Features: Chemical Resistant , UV Resistant , Impact Resistant , Abrasion Resistant , Non-Slip
    • Grade Standard: Industrial Grade

    Nitocote ET140 is based on solvent-free epoxy resins modified with coal tar pitch. It is supplied as a two pack materials in pre-weighed quantities ready for on-site mixing and use.

    Nitocote ET140 is applied as a two coat application.

    • High build, single coat application
    • Good chemical resistance.
    • Primerless.
    • Excellent hold-out on vertical surfaces.
    • Moderate flexibility.

    Details -

    • Pot life - 2  hrs
    • Time between coats- 4 hrs
    • Full hardness- 24hrs
    • Full Cure- 7 days
    • Compressive Strength -40  N/mm2

    Nitocote EP405

    Product Details:
    • Classification: Self Levelling , Mortar Epoxy Coating, Gravelled Epoxy Coating, Epoxy Antistatic Floor
    • Types: Solid , Solvent Based , Water Based
    • Application Method: Spray , Brush , Roller , Water

    Nitocote EP405 is based on solvent-free epoxy resins modified with coal tar pitch. It is supplied as a two pack materials in pre-weighed quantities ready for on-site mixing and use.

    Nitocote EP405 is applied as a two coat application.

    • High build, single coat application
    • Good chemical resistance.
    • Primerless.
    • Excellent hold-out on vertical surfaces.
    • Moderate flexibility.

    Details -

    • Pot life - 2  hrs
    • Time between coats- 4 hrs
    • Full hardness- 24hrs
    • Full Cure- 7 days
    • Compressive Strength -40  N/mm2

    Reebol Emulsion XTRA

    Reebol Emulsion Xtra is supplied as a pale amber liquid which turns white when diluted with water to produce a chemical release agent, combining the outstanding release properties of such materials with the economy of a conventional oil. It reacts with the alkali in the concrete to form a thin water repellent skin on the surface of the mould which enables easy stripping from the hardened concrete.

    • Non-staining : No cleaning of unsightly oil stains if plastering is not required.
    • High quality : Produces really fair faced fi nish concrete.
    • Versatile : Can be used on all types of moulds.
    • Minimises cleaning : Makes cleaning of form faces between pours very easy.
    • Concentrate form : Reduces storage and transport costs.
    • Water based : Only requires water for dilution.
    • Aids corrosion inhibition.
    Details -
    • Specific Gravity- Typically 0.960 at 25C
    • Dilution    rate-  1  part  Reebol  Emulsion  Xtra:  6parts  clear water (by volume)
    • Flash  point  - Reebol  Emulsion  Xtra  is  approximately  61 C

    Renderoc CS

    Product Details:
    • Brand : Fosroc

    Renderoc CS is used for sealing cracks on plaster, masonryand concrete substrates.
    details -
    • Colour -White
    • Setting time -15 to 20 min
    • Compressive  strength -22 N/mm2 in 7 days
    • Fresh  wet  density 1.95  g/cc W/p Ratio 0.36
    • Mix proportions by volume 1 part water : 2.5 -3 parts of powder
    • Minimum  application temperature -10C

    Conplast NC

    Conplast NC chloride-free accelerating admixture is supplied as a light straw-coloured solution that instantly disperses in water.

    Conplast NC accelerates the early stages of cement hydration, producing more rapid stiffening and allowing strength gain to commence at an earlier stage. This effect is particularly noticeable at low temperatures and is most significant in the first 24 hours after mixing.

    Advantages:

    • Particularly effective in assisting to offset the delaying effect of low temperatures on setting and strength gain. 
    • Accelerated setting gives added protection against early age frost attack.
    • Also provides a degree of water reduction or increased workability.
    • Suitable for use in bricklaying mortar.
    • Chloride-free, safe for use in reinforced concrete.

    Properties

    • Specific gravity: 1.260 - 1.270 at 30C
    • Freezing point:  -16C
    • Chloride content:  Nil to BS 5075
    • Air entrainment:  Less than 1%

    Conplast P211

    Product Details:
    • Brand: Fosroc

    Conplast P211 is a chloride free water-reducing admixture based on selected sugar-reduced lignosulphonates. It is supplied as a brown solution which instantly disperses in water.

    Conplast P211 disperses the fine particles in the concrete mix, enabling the water content of the concrete to perform more effectively and improving the consistency of the concrete. This produces higher levels of workability for the same water content, allowing benefits such as water reduction and increased strengths to be taken.

    Advantages:

    • Allows specified strength grades to be met at reduced cement content or increased workability.
    • Water reduction significantly improves compressive strengths at all ages and enhances durability through the production of low permeability concrete.
    • Minimises the risk of segregation and bleeding and assists in the production of a dense, close textured surface, improving durability.
    • Chloride free, safe for use in pre-stressed and reinforced concrete.

    Properties

    • Specific gravity: 1.150 - 1.170 @25C
    • Appearance- brown liquid
    • Chloride content-Nil to IS:456

    Nitobond EP Hardener

    Product Details:
    • Surface of Application: Ceramic
    • Grade Standard: Industrial Grade
    • Features: Impact Resistant, Moisture Resistant, Vibration Resistant, Heat Resistant, Water Resistant
    • Brand: Fosroc

    Nitobond EP is based on solvent-free epoxy resins containing pigments and fine fillers. It is supplied as a two-part material in pre-weighed quantities ready for onsite mixing and use.
    Coloured components, white base and green hardener, provide visual evidence that adequate mixing is achieved.

    • Can be applied to dry or damp surfaces
    • High mechanical strength
    • Good positive adhesion
    • Can be applied where a substrate/repair barrier is required
    • Standard and slow set grades

    Details -

    • Pot life - Min. 120 minutes @ 35C
    • Full hardness- 24hrs
    • Full Cure- 7 days
    • Compressive Strength -40  N/mm2

    Nitoseal PU180 Hardener

    Nitoseal PU180 two-part pouring grade sealant is formulated from a blend of epoxy and urethane polymers. The mixed sealant is self levelling and can be poured directly into horizontal joints to form a tough resilient seal possessing a limited degree of flexibility.

    Nitoseal PU180 is available in a range of attractive colours with a separate colour pack providing visual mixing control.

    • Load bearing for support of arises under heavy wheel load
    • Good resistance to chemicals and hydrocarbon fuels
    • Excellent adhesion without primer to dry clean concrete
    • Pouring grade ensures ease of placing
    • Suitable for use in wide joints
    • Self levelling to produce uniform and neat joints
    • Suitable for use in Middle East conditions

    Details -

    • Specific gravity:1.2
    • Movement accommodation factor:20%
    • Shore ‘A’ hardness:15 to 25 (14 days at 20oC)

    Nitotile Grout

    Product Details:
    • Brand: Fosroc

    Nitotile Grout is a blend of specially selected cement, fillers and synthetic organic polymers. When added to water it readily blends to produce a smooth creamy paste which when set is water and mould resistant. Nitotile Grout is used in conjunction with Nitotile* tile adhesives. Standard colours are available.

    • Tropical grade to suit Middle East working conditions.
    • Mould resistant.
    • Thixotropic, non-slump application.
    • One part and only requires water addition.
    • Water-resistant.
    • Can be used in submerged conditions.
    • Available in a range of attractive colours.

    details -

    Typical Properties of mixed material.

    • Specific Gravity:1.60
    • Pot life @ 27C:30 - 35 min
    • Foot traffic:24  hrs
    • Full cure:21  days
    Looking for Fosroc Construction Chemicals ?
    © Mahavir Chemical Industries
     
    Desktop Site Back to top